wheelie
04-21-2009, 07:49 PM
Engine is listed on ebay right now....NO RESERVE....Will assist with tuning...Must move some stuff out of my way!
Bidding starts at $500
http://cgi.ebay.com/ebaymotors/ws/eBayISAP...em=260397769232 (http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=260397769232)
400" Small Block Ford Turbo Engine
This is a Ford 400" Small Block Twin Turbo Engine, this is a killer engine. Built by Kuntz & Company. Ran 6.50s at 221MPH, went 176MPH in the 1/8th mile. Engine would cost $30,000 to duplicate. The intake manifold alone would cost $2,400 to replace. Will provide complete engine specs when engine is purchased (such as cam specs).
Engine Specs:
SVO Block, W351 Siamese
Yates Heads, Fully Ported by Kuntz & Co
Custom Turbo Cam by Kuntz & Co
Hogan Sheetmetal EFI Manifold w/Billet Fuel Rails (not pictured)
Accufab 90mm T/B with TPS
Fabricated Sheetmetal Valvecovers
GRP Pro Mod Aluminum Rods w/ARP Bolts (29 Runs)
Venolia Pistons
Jesel Rockers
"Pro Pan" Dry Sump Fabricated Pan (3 Scavenge Fittings on Pan)
MSD Distributor
Innovators West Balancer
Felpro Gaskets
ARP 3/8 Exhaust Studs
Engine has 16 runs since fresh, 29 runs on rods (we normally put 90-100 runs on rods). This engine ran in the 4.30s at 176mph last time out on 10.5 tires. Makes legitimate power, and we have the time slips to back it up. Please email dan@hyperformanceracing.com with questions.
http://www.hyperformanceracing.com/ebay/400_yates1.jpg
http://www.hyperformanceracing.com/ebay/400_yates2.jpg
http://www.hyperformanceracing.com/ebay/400engine.jpg
http://www.hyperformanceracing.com/ebay/400balancer.jpg
http://www.hyperformanceracing.com/ebay/400pan.jpg
http://www.hyperformanceracing.com/ebay/400hogans.jpg
Bidding starts at $500
http://cgi.ebay.com/ebaymotors/ws/eBayISAP...em=260397769232 (http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=260397769232)
400" Small Block Ford Turbo Engine
This is a Ford 400" Small Block Twin Turbo Engine, this is a killer engine. Built by Kuntz & Company. Ran 6.50s at 221MPH, went 176MPH in the 1/8th mile. Engine would cost $30,000 to duplicate. The intake manifold alone would cost $2,400 to replace. Will provide complete engine specs when engine is purchased (such as cam specs).
Engine Specs:
SVO Block, W351 Siamese
Yates Heads, Fully Ported by Kuntz & Co
Custom Turbo Cam by Kuntz & Co
Hogan Sheetmetal EFI Manifold w/Billet Fuel Rails (not pictured)
Accufab 90mm T/B with TPS
Fabricated Sheetmetal Valvecovers
GRP Pro Mod Aluminum Rods w/ARP Bolts (29 Runs)
Venolia Pistons
Jesel Rockers
"Pro Pan" Dry Sump Fabricated Pan (3 Scavenge Fittings on Pan)
MSD Distributor
Innovators West Balancer
Felpro Gaskets
ARP 3/8 Exhaust Studs
Engine has 16 runs since fresh, 29 runs on rods (we normally put 90-100 runs on rods). This engine ran in the 4.30s at 176mph last time out on 10.5 tires. Makes legitimate power, and we have the time slips to back it up. Please email dan@hyperformanceracing.com with questions.
http://www.hyperformanceracing.com/ebay/400_yates1.jpg
http://www.hyperformanceracing.com/ebay/400_yates2.jpg
http://www.hyperformanceracing.com/ebay/400engine.jpg
http://www.hyperformanceracing.com/ebay/400balancer.jpg
http://www.hyperformanceracing.com/ebay/400pan.jpg
http://www.hyperformanceracing.com/ebay/400hogans.jpg